Gun care..

[HiImSeth]

So.. laugh all you want but I'm a noob and wanting to take real good care of my handguns, or well, any gun I own I guess. But, I've not really shot them much or done a lot with them until now. I'm ready to start spending time shooting them more and enjoying them. With that, I'll need to know the right way to clean them and keep them oiled and in good shape. No one in my family has ever been a gun fanatic or anything so I've not had anyone to learn from. I basically pick it up on my own (for better or worse, idk). So if there is a link or anything out there or any of you feel like writing up a "HOWTO" on cleaning guns the right way, with the right stuff, and keeping them in good shape, that'd be excellent. I'm looking for suggestions on the best solvents/oils/brushes and of course how to use them. Pretty easy request, right? =] In searching I found that most use/recommend Breakfree CLP and #9.. but no definite guide or anything.

Thanks in advance!

[pete156]

I'm in the same boat. I've been fooling with guns for a couple of years now and have just had to kinda learn as I go.

I have found that you are more likely to find a cleaning tutorial on specific guns, but not just a general guide. You might trying doing a google search for "(insert gun name here) cleainging instructions or guide). I did a little better after I started doing that.

It may sound dumb to the other more experienced folks around here, but cleaning and whatnot can seem overwhelmig to a noob. I wasn't sure what parts of the gun to use the solvents on (ie: finish also or just the internals)

I'm sure I'm still not doing completely right, but surely I'm close. :)

[HiImSeth]

Hah, so glad to see I'm not all by myself on this one.

[kgull85]

Hah, so glad to see I'm not all by myself on this one.

+1

I have been able to find cleaning/lubing guides specifically for my Kahr P9 and Kel-Tec P3AT, but I havn't found a "General gun cleaning/lubing guide".

[ADDO]

Here is a step by step course on how to clean a revolver that might interest you:

http://www.doc.state.ok.us/Training/Review%20For%20Cleaning%20A%20Revolver%20Online_fi les/frame.htm

[skyydiver]

Great link, ADDO. Here is one for glocks with a link to pics of lube points...
Glockmeister (http://www.glockmeister.com/gclean.shtml)

[burner]

I clean my Glocks with Hoppe 9 and breakfree from Wallyworld.
I just scrub out the barrel and wipe everything else down.Glocks are more low maintenance than some other guns,I think.

[Cowman]

Try this, www.actionsbyt.blogspot.com . I use the micro x. Works good. Regards

[Scott_In_OKC]

I use Simple Green when cleaning the Glocks. I mix the Simple Green 1:1 with water in a spray bottle. I completely strip the Glock and pour enough of the mixture in a bowl to cover all the small pieces and barrel. While those are soaking, I spray down the slide and frame with the Simple Green mixture, scrub with a toothbrush and rinse with HOT water. Set them aside to dry. Now scrub all the small pieces and barrel. Again, rinse with HOT water. Use a hair dryer to completely dry all pieces, reassemble, and lube per the manual. You will be amazed at how clean your weapon is and you have not used any nasty solvents.

[HiImSeth]

I use Simple Green when cleaning the Glocks. I mix the Simple Green 1:1 with water in a spray bottle. I completely strip the Glock and pour enough of the mixture in a bowl to cover all the small pieces and barrel. While those are soaking, I spray down the slide and frame with the Simple Green mixture, scrub with a toothbrush and rinse with HOT water. Set them aside to dry. Now scrub all the small pieces and barrel. Again, rinse with HOT water. Use a hair dryer to completely dry all pieces, reassemble, and lube per the manual. You will be amazed at how clean your weapon is and you have not used any nasty solvents.
Ah, good post. That's what I need.. =]

[HiImSeth]

Try this, www.actionsbyt.blogspot.com . I use the micro x. Works good. RegardsGood link as well, thank you!

[dogbear]

Can someone show us a website or show us where some of the places are that were not suppose to oil.Like the firing pin channel,extractor,breech face,chamber and feed ramp.Thanks

[c10bonanza]

I use Simple Green when cleaning the Glocks. I mix the Simple Green 1:1 with water in a spray bottle. I completely strip the Glock and pour enough of the mixture in a bowl to cover all the small pieces and barrel. While those are soaking, I spray down the slide and frame with the Simple Green mixture, scrub with a toothbrush and rinse with HOT water. Set them aside to dry. Now scrub all the small pieces and barrel. Again, rinse with HOT water. Use a hair dryer to completely dry all pieces, reassemble, and lube per the manual. You will be amazed at how clean your weapon is and you have not used any nasty solvents.


This is how I clean my Glocks and PM9 as well. I used to use solvents and gun cleaners, but got tired of inhaling the noxious fumes and having to wear gloves. Simple Green does the trick, and I can clean them in my kitchen!!

[Oklahoma]

why don't -all- the manufacturers give detailed cleaning/lubing instructions in their owners manuels adn their websites?? seems like they would have less warranty probs and consumer complaints if they gave advice on keeping their products maintained properly.

[skyydiver]

I use Simple Green when cleaning the Glocks. I mix the Simple Green 1:1 with water in a spray bottle. I completely strip the Glock and pour enough of the mixture in a bowl to cover all the small pieces and barrel. While those are soaking, I spray down the slide and frame with the Simple Green mixture, scrub with a toothbrush and rinse with HOT water. Set them aside to dry. Now scrub all the small pieces and barrel. Again, rinse with HOT water. Use a hair dryer to completely dry all pieces, reassemble, and lube per the manual. You will be amazed at how clean your weapon is and you have not used any nasty solvents.

Okay, I want to try this, but I don't trust myself. How much rinsing does it take to get all the simple green off, especially out of all the nooks and crannies in the frame? Also, how long does it take to dry everything? Just want an idea, so as not to rust my blaster trying something new.