Jumping into form 1 cans

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Oklahomabassin

Sharpshooter
Special Hen
Joined
Mar 27, 2007
Messages
24,973
Reaction score
23,411
Location
America!
For the love of all that is good, you guys need to share pictures of your homemade cans. I was wanting to do this but then forgot all about it until this zombie thread popped back up a few days ago. Let’s see what these things look like
Most aren't going to look much different externally other than the engraving and possibly the finish. Internals is where you are likely to see the difference but not always.

It can be a lot quicker to have a suppressor in hand using the Form 1 option.
 

Seadog

Sharpshooter
Supporting Member
Special Hen Supporter
Joined
Sep 22, 2009
Messages
5,664
Reaction score
6,971
Location
Boondocks
Most aren't going to look much different externally other than the engraving and possibly the finish. Internals is where you are likely to see the difference but not always.

It can be a lot quicker to have a suppressor in hand using the Form 1 option.

I’d like to make a can that is on the bigger side. Kind of like the ones there were made for the MAC10s back in the 70s-80s. Shoot if I liked my first one I’d probably end up making more of them.
 

Oklahomabassin

Sharpshooter
Special Hen
Joined
Mar 27, 2007
Messages
24,973
Reaction score
23,411
Location
America!
I’d like to make a can that is on the bigger side. Kind of like the ones there were made for the MAC10s back in the 70s-80s. Shoot if I liked my first one I’d probably end up making more of them.
You submit your overall length and caliber IIRC on your application. You can build it as big as you want.
 

Fredkrueger100

Dream Master
Supporting Member
Special Hen Supporter
Joined
Aug 16, 2012
Messages
7,867
Reaction score
6,169
Location
Shawnee, OK
I am fixing to buy one from Quiet Bore. Do I have to do fingerprints and pictures or do I just fill out the form 1 E file and pay the $200? I’ve never done it before. Any help is greatly appreciated.
 

mr ed

Sharpshooter
Supporting Member
Special Hen Supporter
Joined
Mar 14, 2009
Messages
6,999
Reaction score
4,834
Location
Tulsa
Go online to the atf eforms site.
Register your name and pass word.
Each time you finish a page, click save up towards the top left.
When you get to make and model
Put under mfgr code FMI that's eff - Mmm - eye. Stands for form one.
Under model a drop down box will appear select N/A.
Figure out your total length your can cannot exceed this length so add a little.
Like an inch for a piston.
For caliber list 22, or 30, or 9mm ,or 45. Not cartridge specific.
After you upload your photo click save, then the view button next to save and it will show the form like the examiner sees it.
Make sure your photo shows up.
Don't matter if it's sideways or upside down they'll fix that. But if it doesn't upload it'll get disapproved and you'll have to wait for refund and start over.

Following the FMI. And N/A will keep it from going into "Pending Research"
Which can delay approval 30 to 90 days.

After you pay and push submit. Within a minute or so you should receive an email with 2 attachments. One is the cover sheet to be included with the prints. The other is a copy of your submitted form. You will need to print off the pages marked cleo copy. 4, 5, 6 I believe and send to your sheriff.
 
Last edited:

Latest posts

Top Bottom