Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Classifieds
Media
New media
New comments
Search media
Log in
Register
What's New?
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Navigation
Install the app
Install
More Options
Advertise with us
Contact Us
Close Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Forums
Hobbies & Interests
Gearheads
'68 GMC Repairs
Search titles only
By:
Reply to Thread
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="Droff" data-source="post: 3731403" data-attributes="member: 26615"><p>I've got a '68 3/4 ton GMC that I'd like to get worked on, I've got some engine and fuel system issues that are causing me some problems. I don't know of a garage that I can say I completely trust so thought I'd ask for some suggestions. The truck has a 350 in it with an Edelbrock carb, auto transmission, fuel tank in the cab.</p><p></p><p>My problems started when I started working on it....... </p><p>I had fuel leaking from the carb and decided I'd rebuild it (my first foray into carb work). I also decided to get the tank cleaned since there was rust in it so I got the tank cleaned and then coated it myself with a POR15 kit. Installed the tank and carb and the truck wouldn't start. Pulled the carb and went through it again, everything looked to be put back together correctly. Installed it again and still no start, just cranking. I now have a couple issues that have popped up. My tank leaked into the cab and through the mounting hole tabs. I'm guessing when I re-installed the tank, it wasn't as sealed as I thought and the seam seperated enough for it to leak. It leaked at every place there was a mounting tab.</p><p></p><p>Also, I have now had fuel get into the engine block and down into the oil pan. I can see it and smell it. Since I had an oil pan leak, all the extra fuel in there has forced more oil out and onto the driveway, so more bonus for me. My best guess is possibly the fuel pump, which is mechanical. I plan on ordering a new tank as well.</p><p></p><p>Since I have a couple things going on and not real sure on troubleshooting, I thought I'd opt to pay someone to get the truck running, it'll get done sooner. Since this is an older 'classic' truck, I'd prefer someone that likes to work on those types of vehicles, whether a business or in their garage. I don't have to have it done quickly, just done and done right. I really like older vehicles, I just seem to know enough to get myself in trouble at times.</p><p></p><p>I figure I need fuel system work as well having the oil pan pulled and gaskets replaced, likely even the rear main seal. Could possibly have engine issues with the fuel getting in there as well. Too many things for me to attack with much confidence. I'm in the Choctaw area.</p><p></p><p>Thanks.</p></blockquote><p></p>
[QUOTE="Droff, post: 3731403, member: 26615"] I've got a '68 3/4 ton GMC that I'd like to get worked on, I've got some engine and fuel system issues that are causing me some problems. I don't know of a garage that I can say I completely trust so thought I'd ask for some suggestions. The truck has a 350 in it with an Edelbrock carb, auto transmission, fuel tank in the cab. My problems started when I started working on it....... I had fuel leaking from the carb and decided I'd rebuild it (my first foray into carb work). I also decided to get the tank cleaned since there was rust in it so I got the tank cleaned and then coated it myself with a POR15 kit. Installed the tank and carb and the truck wouldn't start. Pulled the carb and went through it again, everything looked to be put back together correctly. Installed it again and still no start, just cranking. I now have a couple issues that have popped up. My tank leaked into the cab and through the mounting hole tabs. I'm guessing when I re-installed the tank, it wasn't as sealed as I thought and the seam seperated enough for it to leak. It leaked at every place there was a mounting tab. Also, I have now had fuel get into the engine block and down into the oil pan. I can see it and smell it. Since I had an oil pan leak, all the extra fuel in there has forced more oil out and onto the driveway, so more bonus for me. My best guess is possibly the fuel pump, which is mechanical. I plan on ordering a new tank as well. Since I have a couple things going on and not real sure on troubleshooting, I thought I'd opt to pay someone to get the truck running, it'll get done sooner. Since this is an older 'classic' truck, I'd prefer someone that likes to work on those types of vehicles, whether a business or in their garage. I don't have to have it done quickly, just done and done right. I really like older vehicles, I just seem to know enough to get myself in trouble at times. I figure I need fuel system work as well having the oil pan pulled and gaskets replaced, likely even the rear main seal. Could possibly have engine issues with the fuel getting in there as well. Too many things for me to attack with much confidence. I'm in the Choctaw area. Thanks. [/QUOTE]
Insert Quotes…
Verification
Post Reply
Forums
Hobbies & Interests
Gearheads
'68 GMC Repairs
Search titles only
By:
Top
Bottom