Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Classifieds
Media
New media
New comments
Search media
Log in
Register
What's New?
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Navigation
Install the app
Install
More Options
Advertise with us
Contact Us
Close Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Forums
The Range
Ammo & Reloading
Found a Vickerman die at the Wanenmacher Show
Search titles only
By:
Reply to Thread
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="Dumpstick" data-source="post: 4246892" data-attributes="member: 41653"><p>Here's one you don't see much. A Vickerman seating die:</p><p>[ATTACH=full]469412[/ATTACH]</p><p></p><p>[ATTACH=full]469418[/ATTACH]</p><p></p><p>Here's how it's put together:</p><p>[ATTACH=full]469415[/ATTACH]</p><p></p><p>It works like this-</p><p> The (caliber specific) center pin, or punch, is stationary during use. The (again, caliber specific) sleeve at the bottom left of the picture slides up and down in the die housing.</p><p>The sleeve is chamfered too rest on the (bottleneck) cartridge shoulder:</p><p>[ATTACH=full]469414[/ATTACH]</p><p></p><p>Screw the die in the press, put a case in there and run it up to get some pressure on the spring. Drop a bullet in the groove - in this case 30 cal; there are different punch/sleeve combos.</p><p></p><p>Push the case up, the groove holds the bullet centered, the punch sets the depth. The bullet never moves during seating; only the cartridge case, captured in the sleeve, moves. In effect, you are pushing the case onto the bullet.</p><p></p><p>This pic shows how filthy the die was at purchase. I dropped it in some carb cleaner for 30 minutes.</p><p>[ATTACH=full]469417[/ATTACH]</p><p>The punch adjusts at the top, held with a small headless screw.</p><p></p><p>Here's a shot after cleaning.</p><p>[ATTACH=full]469413[/ATTACH]</p><p></p><p>It works as well as the newer version - many other makers have a version similar, but most without the window. I know Forster makes one, and all the more 'boutique (read: more expensive) makers have something like it.</p><p></p><p>I had an old Pacific window die for 6.5x55, but I let it go when I sold my M96. I shouldn't have let either the rifle or the die go, but...</p></blockquote><p></p>
[QUOTE="Dumpstick, post: 4246892, member: 41653"] Here's one you don't see much. A Vickerman seating die: [ATTACH type="full" alt="DSCF0074.JPG"]469412[/ATTACH] [ATTACH type="full" alt="DSCF0072.JPG"]469418[/ATTACH] Here's how it's put together: [ATTACH type="full" alt="DSCF0075.JPG"]469415[/ATTACH] It works like this- The (caliber specific) center pin, or punch, is stationary during use. The (again, caliber specific) sleeve at the bottom left of the picture slides up and down in the die housing. The sleeve is chamfered too rest on the (bottleneck) cartridge shoulder: [ATTACH type="full" alt="DSCF0076.JPG"]469414[/ATTACH] Screw the die in the press, put a case in there and run it up to get some pressure on the spring. Drop a bullet in the groove - in this case 30 cal; there are different punch/sleeve combos. Push the case up, the groove holds the bullet centered, the punch sets the depth. The bullet never moves during seating; only the cartridge case, captured in the sleeve, moves. In effect, you are pushing the case onto the bullet. This pic shows how filthy the die was at purchase. I dropped it in some carb cleaner for 30 minutes. [ATTACH type="full" alt="DSCF0073.JPG"]469417[/ATTACH] The punch adjusts at the top, held with a small headless screw. Here's a shot after cleaning. [ATTACH type="full" alt="DSCF0077.JPG"]469413[/ATTACH] It works as well as the newer version - many other makers have a version similar, but most without the window. I know Forster makes one, and all the more 'boutique (read: more expensive) makers have something like it. I had an old Pacific window die for 6.5x55, but I let it go when I sold my M96. I shouldn't have let either the rifle or the die go, but... [/QUOTE]
Insert Quotes…
Verification
Post Reply
Forums
The Range
Ammo & Reloading
Found a Vickerman die at the Wanenmacher Show
Search titles only
By:
Top
Bottom