Official druryj Pay it Forward exchange

[RickN]

A long shot here but one of you car guys might have a need for these. I have 2 new, in the box, door jamb switches that fit the following older models. Pick them up in Edmond as I do not get around much.


FORD FAIRLANE 1970
FORD FALCON 1970
FORD LTD 1970-1978
FORD LTD II 1977-1979
FORD MAVERICK 1970-1975
FORD MUSTANG 1970-1973
FORD RANCHERO 1970-1976
FORD THUNDERBIRD 1968-1979
FORD TORINO 1970-1976
LINCOLN CONTINENTAL 1970-1979
LINCOLN MARK III 1970-1971
LINCOLN MARK IV 1972-1976
LINCOLN MARK V 1977-1979
LINCOLN VERSAILLES 1977-1979
MERCURY COMET 1971-1976
MERCURY COUGAR 1968-1979
MERCURY GRAND MARQUIS 1975-1978
MERCURY MARQUIS 1970-1978
MERCURY MONTEGO 1968-1976

 

[SlugSlinger]

This is the first stropping wheel I made. It fits an 8” bench grinder with a 5/8” arbor. It fits on my bench grinder but the big centering washers will not fit with this wheel because of its width. It’s 1.5” wide. This will put a razors edge on your knife or anything else you want to cut hair with. You use this after you sharpen your knife using a stone or other method. It’s loaded with green polishing compound.
I live east of Owasso if you want to come and get it.

 

[dlbleak]

Man, wish I was closer

 

[druryj]

I have a excellent condition HP Officejetpro 8600 Printer Scanner Copier Fax unit I will happily pay it forward to an established member with substantial posts. This was like $229 new, but I have no need for it and it takes up too much space on my small desk. I have all the cords, the manual, and papers that came with it. Unfortunately, the box has been chunked. I want this to go to someone who can use it; not to someone who is going to turn around and post it in the Classifieds. That would highly irritate me if that were to happen.
Pick this up in Yukon, near Reno and Mustang Road. You will also need to make sure you follow up by posting something in this P.I.F. section to keep the thread alive and kicking.
PM me if you need a good All-In-One Unit.

See this excellent printer copier scanner fax unit? This one here? You can have it for free. Just PM me and we will make it happen. Happy New Year!


Sent from my iPhone using Tapatalk

 

[dlbleak]

Brother project 551. Carrying case ,foot pedal, etc. works fine as far as I know. Pics don’t show it but it’s a cool vintage light blue color. Pm me if interested

 

[DavidMcmillan]

I have a small safe that is taking up a space I'd like to use for another purpose. I haven't used this safe for over a year so it really is just an extra. Great condition except for an internal issue that drains the battery, so I just connect the battery only when I'm opening it. So, it can be yours!

Measures 16x17x18 roughly...

In the Moore-Norman area.

 

[druryj]

s

See this excellent printer copier scanner fax unit? This one here? You can have it for free. Just PM me and we will make it happen. Happy New Year!


Sent from my iPhone using Tapatalk[/QUOTE

It is still available, somebody needs this! It would be great for a small business or if you print a lot at home

 

[DavidMcmillan]

I apologize for my delay, but the safe has been picked up by one of our members. A couple of you have asked about it and my excuse for forgetting to close it out is that being retired is just so time consuming, I can't get everything done! Thanks OSA.

 

[druryj]

I'm gonna give this very nice 4--in 1 printer shown in post #344 to the Disabled Vets truck next week unless somebody says they want it.

 

[dlbleak]

Power washer. It’s a Glidden 2000. Wisconsin Robin side shaft motor. The motor could be used for many things. It’s a 7 or 8 horse and will bump on ether. Compression is strong. I put a Chinese carb that was supposed to be the same. It is but the linkage for the governor is a little different. It needs an gas tank but that’s a simple fix. A guy with a little more time and knowledge could have it purring like Stormy Daniels! Free free free!