Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Classifieds
Media
New media
New comments
Search media
Log in
Register
What's New?
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Navigation
Install the app
Install
More Options
Advertise with us
Contact Us
Close Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Forums
The Water Cooler
Photo Album
Show off your .45!
Search titles only
By:
Reply to Thread
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="ez bake" data-source="post: 817150" data-attributes="member: 229"><p>I hate to sell the old girl, but since I finally got around to typing up what all she had done to her, I guess I owe it to her to post it here.</p><p></p><p>This is a Thompson Custom 1911 (stainless) with quite a bit of gunsmithing from the good Dr. Barry Greyson on this board (arguably one of the best 1911 gunsmiths in this state). </p><p></p><p>The fit and finish of this gun are amazing and the slide/frame feels like glass. It is accurate, has one of the nicest triggers I've ever felt on a 1911 (and its a series 80 firing pin safety model - a fact that no one I've asked to pull the trigger can seem to guess). The sear spring in it now is super-light, but it comes with another sear spring that makes for a more carry-friendly trigger should you want to use it for self defense. </p><p></p><p>This gun is a friggin shooter. I've got about 800rds through it and it was broken in properly and has always been well maintained. I've got every piece of paperwork from anything ever done to it (except for the brownells receipt from the parts). I bought this one new and have been its only owner.</p><p></p><p>I've got a full write-up of what he did.</p><p></p><p>Here's directly from the write-up:</p><p></p><p>1. Adjusted and lowered feet of barrel / and side of hood; and clearanced barrel hood .003" to breech face.</p><p></p><p>2. Crown barrel, eliminate barrel spring at bushing; adjusted timing.</p><p></p><p>3. Check headspace and ream and polish chamber</p><p></p><p>4. Throated barrel and frame and set barrel/frame offset.</p><p></p><p>5. Replaced / tuned and advanced timing on upper firing pin safety lever with a Colt series 80 lever and adjusted to fit / timed. Also polished firing pin safety</p><p></p><p>6. New recessed lanyard loop (Guncrafter) mainspring housing - polished internal spring channel and setup with new MS Cap, lower spring base and MS pin (EGW).</p><p></p><p>7. Adjusted hammer strut and clearanced to eliminate msh interference and sear spring rubbing</p><p></p><p>8. Fit Thumb safety and bevel & smooth edges</p><p></p><p>9. Adjust and install new series 80 (blue) Ed Brown Extractor</p><p></p><p>10. Adjust the "Swelled" Kimber mag to .538 to drop free.</p><p></p><p>11. Install and adjust new Ed Brown National Match Trigger</p><p></p><p>12. Install and adjust Ed Brown Series 80 Firing Pin stop (stainless)</p><p></p><p>13. Polish internals of Mag Release.</p><p></p><p>14. Replaced hammer and sear pins with EGW Hardened pins</p><p></p><p>15. Adjusted grip safety to release properly with new mainspring housing.</p><p></p><p>16. Adjusted and belveled most of the sharp edges inside of the slide and on rails.</p><p></p><p>17. Beveled barrel bushing and polished edges.</p><p></p><p>18. Installed new Firing Pin spring and recoil spring (I.S.M.I) 16Lbs (also bevel FP hole on breech face).</p><p></p><p></p><p></p><p></p><p></p><p><strong>Here's the parts list:</strong></p><p></p><p>1. Hammer, Sear, Disconnector, hammer strut (all Cylinder and Slide), Hammer Strut Pin (EGW).</p><p></p><p>2. Hammer and Sear Pins (EGW)</p><p></p><p>3. Nowlin Lt. Sear Spring</p><p></p><p>4. Ed Brown HardCore Sear Spring</p><p></p><p>5. Wolff F.P. Spring</p><p></p><p>6. #1 Colt Series 80 upper safety lever</p><p></p><p>7. Ed Brown Thumb Safety (this was later replaced with a stainless standard-width Wilson or C&S, I can't remember, but Barry did the work).</p><p></p><p>8. Guncrafter recessed Lanyard loop mainspring housing.</p><p></p><p>9. Trigger (Ed Brown National Match), Extractor (Ed Brown), firing pin stop (EGW).</p><p></p><p>10. Wilson Combat stainless grip screws / bushings and some wood grips I got off of another member here (there is a small nick in the top of the wooden grips, by the thumb safety, its barely noticable and has never bothered me, so I never replaced them).</p><p></p><p></p><p></p><p><strong>[Broken External Image]</strong></p><p></p><p></p><p></p><p><strong>[Broken External Image]</strong></p><p></p><p></p><p></p><p><strong>[Broken External Image]</strong></p><p></p><p></p><p></p><p><strong>[Broken External Image]</strong></p></blockquote><p></p>
[QUOTE="ez bake, post: 817150, member: 229"] I hate to sell the old girl, but since I finally got around to typing up what all she had done to her, I guess I owe it to her to post it here. This is a Thompson Custom 1911 (stainless) with quite a bit of gunsmithing from the good Dr. Barry Greyson on this board (arguably one of the best 1911 gunsmiths in this state). The fit and finish of this gun are amazing and the slide/frame feels like glass. It is accurate, has one of the nicest triggers I've ever felt on a 1911 (and its a series 80 firing pin safety model - a fact that no one I've asked to pull the trigger can seem to guess). The sear spring in it now is super-light, but it comes with another sear spring that makes for a more carry-friendly trigger should you want to use it for self defense. This gun is a friggin shooter. I've got about 800rds through it and it was broken in properly and has always been well maintained. I've got every piece of paperwork from anything ever done to it (except for the brownells receipt from the parts). I bought this one new and have been its only owner. I've got a full write-up of what he did. Here's directly from the write-up: 1. Adjusted and lowered feet of barrel / and side of hood; and clearanced barrel hood .003" to breech face. 2. Crown barrel, eliminate barrel spring at bushing; adjusted timing. 3. Check headspace and ream and polish chamber 4. Throated barrel and frame and set barrel/frame offset. 5. Replaced / tuned and advanced timing on upper firing pin safety lever with a Colt series 80 lever and adjusted to fit / timed. Also polished firing pin safety 6. New recessed lanyard loop (Guncrafter) mainspring housing - polished internal spring channel and setup with new MS Cap, lower spring base and MS pin (EGW). 7. Adjusted hammer strut and clearanced to eliminate msh interference and sear spring rubbing 8. Fit Thumb safety and bevel & smooth edges 9. Adjust and install new series 80 (blue) Ed Brown Extractor 10. Adjust the "Swelled" Kimber mag to .538 to drop free. 11. Install and adjust new Ed Brown National Match Trigger 12. Install and adjust Ed Brown Series 80 Firing Pin stop (stainless) 13. Polish internals of Mag Release. 14. Replaced hammer and sear pins with EGW Hardened pins 15. Adjusted grip safety to release properly with new mainspring housing. 16. Adjusted and belveled most of the sharp edges inside of the slide and on rails. 17. Beveled barrel bushing and polished edges. 18. Installed new Firing Pin spring and recoil spring (I.S.M.I) 16Lbs (also bevel FP hole on breech face). [B]Here's the parts list:[/B] 1. Hammer, Sear, Disconnector, hammer strut (all Cylinder and Slide), Hammer Strut Pin (EGW). 2. Hammer and Sear Pins (EGW) 3. Nowlin Lt. Sear Spring 4. Ed Brown HardCore Sear Spring 5. Wolff F.P. Spring 6. #1 Colt Series 80 upper safety lever 7. Ed Brown Thumb Safety (this was later replaced with a stainless standard-width Wilson or C&S, I can't remember, but Barry did the work). 8. Guncrafter recessed Lanyard loop mainspring housing. 9. Trigger (Ed Brown National Match), Extractor (Ed Brown), firing pin stop (EGW). 10. Wilson Combat stainless grip screws / bushings and some wood grips I got off of another member here (there is a small nick in the top of the wooden grips, by the thumb safety, its barely noticable and has never bothered me, so I never replaced them). [b][Broken External Image][/b] [b][Broken External Image][/b] [b][Broken External Image][/b] [b][Broken External Image][/b] [/QUOTE]
Insert Quotes…
Verification
Post Reply
Forums
The Water Cooler
Photo Album
Show off your .45!
Search titles only
By:
Top
Bottom