Electrical Question

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

DavidMcmillan

Sharpshooter
Supporting Member
Special Hen Supporter
Joined
Apr 14, 2010
Messages
10,100
Reaction score
15,265
Location
Oklahoma City
One fixture with three bulbs. It will work with two LEDs and one incandescent, in any combination. No matter which two sockets I use for LED, the third one will only work with incandescent. I have never encountered anything like it. I may have to replace the fixture. Crazy!

Thanks for all the suggestions. I’ll post when this mystery is solved.
 

swampratt

Sharpshooter
Supporting Member
Special Hen Supporter
Joined
Nov 3, 2010
Messages
13,337
Reaction score
21,495
Location
yukon ok
You are trying the same 3 bulbs correct?

Pull all 3 bulbs from the other bathroom that work in that other 3 light fixture and try them.

I am going with one of the wires on the fixture has been reversed.
Some LED bulbs are polarity sensitive as was stated.
 

rickm

Sharpshooter
Special Hen
Joined
Aug 14, 2012
Messages
3,325
Reaction score
4,540
Location
Durant
Not saying this is your problem but i have run across some sockets that wont let the bulb screw in far enough and then i have also come across some bulbs that the screw in part is to short also so if you get one or the other or a combination of both the bulb wont work.
 

KOPBET

Duck of Death
Supporting Member
Special Hen Supporter
Joined
Jun 28, 2008
Messages
13,734
Reaction score
10,395
Location
N36º11.90´ W95º53.29´
Are the working and non-working fixtures on the same circuit breaker?

If not, check the breaker for the non-working fixture, connection at the breaker, and it's associated neutral wire connection at the bus bar for loose or corroded connections. As mentioned, check the connections at the fixture as well and the switch leg at the switch. Make sure the switch leg is actually the hot side.
 

SoonerP226

Sharpshooter
Special Hen
Joined
Jan 1, 2013
Messages
14,378
Reaction score
15,868
Location
Norman
Some LED bulbs are polarity sensitive as was stated.
If it were a polarity issue, it should always happen in the same socket, but, if I read it correctly, the LED bulbs will work in all three sockets, just not if all three sockets have LED bulbs in them. To me, that points to a voltage issue, where there's not enough voltage to activate the third LED. I'd look for bad connections, or maybe corrosion on the contacts. An incandescent bulb isn't as voltage-sensitive, so it'll work, just dimly, if it's under voltage, whereas an LED needs a certain amount of voltage to work.
 

Snattlerake

Conservitum Americum
Special Hen
Joined
Jan 19, 2019
Messages
22,195
Reaction score
35,675
Location
OKC
You are trying the same 3 bulbs correct?

Pull all 3 bulbs from the other bathroom that work in that other 3 light fixture and try them.

I am going with one of the wires on the fixture has been reversed.
Some LED bulbs are polarity sensitive as was stated.
If he has a meter, he can find out. Put the meter on continuity or OHMS.
With the A/C power DISCONNECTED! BOTH WIRES!

Touch one lead to the center of one light fixture then the center of the second. If your meter is on continuity, it will show "0.". and may beep continuously until the circuit is broken.
If OHMS, it will show "0.3 to 0.4" or somewhere in that range.
Now with the first lead still on the first fixture's center, check the third fixture's center. The readings should be the same.

I would then do the same test on the metal sides where the threads are in the fixture. It should be the same readings.

The third check would be just to make sure there are no shorts between the center and the sides

Do all three checks and it will discount any crossed wires.
 

turkeyrun

Sharpshooter
Special Hen
Joined
Feb 11, 2013
Messages
10,271
Reaction score
10,967
Location
Walters
All 3 work
But not with 3 LEDs.
2 LED and 1 incandescent, in any configuration. Contact is being made, bulbs do work.

Fixture is at fault, but where, I have no idea.

I have a bathroom light that had incandescent bulbs, worked perfectly, for years. Changed to LED, nothing works. Put incandescent back in, doesn't work.
Put up new fixture. All working fine.
 

Snattlerake

Conservitum Americum
Special Hen
Joined
Jan 19, 2019
Messages
22,195
Reaction score
35,675
Location
OKC
If it were a polarity issue, it should always happen in the same socket, but, if I read it correctly, the LED bulbs will work in all three sockets, just not if all three sockets have LED bulbs in them. To me, that points to a voltage issue, where there's not enough voltage to activate the third LED. I'd look for bad connections, or maybe corrosion on the contacts. An incandescent bulb isn't as voltage-sensitive, so it'll work, just dimly, if it's under voltage, whereas an LED needs a certain amount of voltage to work.
I like this. LEDs use a bit of the voltage to power their circuit and bridge rectifier, which changes A/C to D/C. It could be just enough of a drain.
 

Firpo

Sharpshooter
Supporting Member
Special Hen Supporter
Joined
Mar 24, 2020
Messages
2,238
Reaction score
6,505
Location
Lawton, Oklahoma
I think @SoonerP226 is right on the money. Can’t be the sockets as the problem moves. Can’t be a polarity issue for the same reason. Gonna have to break out the voltmeter and see what you have. My guess is either a lose connection in the fixture or a wire-nut or a voltage problem. Could even be a worn out breaker at the panel but that would be down the list on things I’d check.
 

Latest posts

Top Bottom